Holiday Gift Ideas & Seasonal Items

 

 Thanksgiving Special:  Free UPS Ground Shipping On Orders Over $50 (U.S. Only)

Harley Highway Pegs
by Kuryakyn

Forward Control Highway Pegs

It's a real challenge to mount a set of highway pegs on a forward control equipped bike. We've done it at last with this very adjustable set-up. Fastening between the forward control and the footpeg. It accepts any Küryakyn footpeg in the primary location and any male mount footpeg in the cruise location.

Standard Cruise Arm Mark IV

Patent Pending

Turn your bike into a lazy boy with our new Cruise Arms! Heavy-duty chrome arms wrap around your stock floorboards just right. So kick back and relax! TV remote and popcorn not included!
 

Mounts to the frame, not the board.

Compatible with Kuryakyn ISO-Boards and all styles of foot boards currently offered by H-D

Offered in short arm or long arm configurations to accommodate all riders.

 Each configuration also allows several inches of fore and aft adjustment to fine tune footpeg position.

 Not compatible with engine guards.

Accepts any H-D style Male Mount Footpeg, sold separately.
 

Sizing Guidelines:

Standard versions are intended for riders with a 30" or shorter inseam.

 Extended versions are intended for riders with a 31" or longer inseam.
 
**These guidelines are approximations only.**

Extended Cruise Arm Mark IV


Patent Pending

Turn your bike into a lazy boy with our new Cruise Arms! Heavy-duty chrome arms wrap around your stock floorboards just right. So kick back and relax! TV remote and popcorn not included.

Mounts to the frame, not the board.

Compatible with Kuryakyn ISO-Boards and all styles of foot boards currently offered by H-D.

Offered in short arm or long arm configurations to accommodate all riders.

 Each configuration also allows several inches of fore and aft adjustment to fine tune footpeg position.

 Not compatible with engine guards.

 Accepts any H-D style Male Mount Footpeg, sold separately.
 

Sizing Guidelines:

Standard versions are intended for riders with a 30" or shorter inseam.

 Extended versions are intended for riders with a 31" or longer inseam.

** These guidelines are approximations only.**
 

Cruise Arm Mark III


This design allows easy installation by simply drilling mounting holes in the steel footboard base for the adjustable mount and full-length reinforcing plate. The entire assembly mounts to the footboard, so the various mounting brackets used by H-D are not a factor. The reinforcing plate adds stiffness to the footboard to keep flex to a minimum. (The stock rubber footboard pads remain unaffected.)

The arms are fully adjustable front to back and are available with or without our cushy ISO-Pegs. Cruise Arm Mark III adjustment is limited when installed on motorcycles with engine guards.

Fits: ’86-’09 FLST Models (ex. '05-'09 FLSTN, , '05-'06 FLSTFSE, '08-'09 FLSTSB, or '09 FLSTC) and ‘84-’09 Electra Glides, (except FLHTCU, '04-'05 FLHTCSE, '06-'09 FLHTCUSE), '84-'91 Tour Glides (except FLHTCU), '98-'09 Road Glides, '94-'09 Road Kings (except '04-'07 FLHRS, '07-'08 FLHRSE)

Important: '84-'08ouring models require support kit, P/N 4533, Cruiser Arm Mark III is not compatabile with firing lowers.

Now for Road King and Dresser
It is now possible to install our Cruise Arm Mark III on H-D Touring models! We have designed a support brace that quickly and easily installs underneath the frame between the footboard mounting brackets. This brace supports the stock brackets and keeps them from flexing under the added leverage of the Cruise Arm Mark III.
 

Cruise Arm Mark III Adapter Kit

ISO-Boards produced after January 1, 2005 are modified to accept our Cruise Arm Mark III highway pegs with the help of this kit. The revised ISO-Boards have pre-drilled holes to accept the mounting bolts. This kit includes reinforcement plates and the fasteners needed to securely attach the Cruise Arm Mark III.
 

Ergo-Plus Engine Guard for Dresser or Road King


U.S. Patent # Des 6,969,083 & 7,073,808

Combining a stylish engine guard with built-in highway pegs, the Ergo Plus Engine Guard brings innovative design to the limits. Use the highway pegs folded-in or flip them out for an optional foot position! Designed with an ergonomic pull back, your feet will feel secure with less outward leg pressure no matter what position you have them in. With a slick mounting system, the Ergo Plus Engine Guard bolts directly to existing mounts on your frame and does not use any clumsy universal clamps. In no time you will be back on the road with your new engine guard and the comfort of multiple foot positions.
 

SwingWing Pegs


 

Enormous numbers of people have asked us how they can stretch their legs a little without spending several hundred dollars for extended controls. Here's the answer. . . a convenient fold-forward, comfortable cruise peg that fastens in place of your stock peg and provides a secondary fold-out peg 3" forward. Replaces any H-D style male-mount peg.

Ergo-Guards
 

U.S. Patent # Des. 6,969,083 & 7,073,808

Küryakyn has rewritten the book on engine guards. For years, engine guard designs have changed very little. By incorporating both tubing and investment cast components into our design, we can create shapes and forms and include features not possible with traditional engine guards. Integrated, folding pegs can be used in either the stowed or deployed position.

Ergo Guard Light Mounting Brackets

With this simple bracket kit, you can easily install Kuryakyn Silver Bullets (or any other light using a 5/16” mounting screw). The kit includes two brackets and hardware to secure them to the existing holes beneath the foot rest area. The Ergo Guard is already drilled to internally route the wiring for a neat and clean appearance.

Recommended options for Silver Bullets include P/Ns 2303, 2319, 2362, and 2363 (Sold Separately - See Silver Bullet Page in Harley Lighting.)

Note: If adding Silver Bullets to function as driving lights, we highly recommend using our Wiring and Relay Kit, P/N 2328, sold separately.
 

The Chrome Mustache™
 

You might just think you died and went to heaven when you go on a long putt with this jewel. Just put your feet up, lean back and enjoy. Sure gets the kinks out of those knees. Available for all ’86-’99 FLST models without engine guards, all ’00-’86 FXST and FLST without Engine Guards, and all '91-'05 Dyna models without forward controls.

Warning: Küryakyn does not recommend using mustache bars on ’85-’99 FXST models or any FXDWG. This product cannot be used safely on these bikes with forward controls because of the close proximity of the peg to the brake pedal.

Adjustable Mustache Bar for Softail and Dyna


 

We’ve taken our tried and trued Mustache Bar and brought it into the 21st Century. The great function of the mustache bar has stayed the same - adding the extra peg positions you need on those cramp-inducing hauls. The difference between old and new lies within the ability to be adjusted to fit virtually any rider. Due to its cleverly designed clamp system, this mustache bar can be moved up or down the downtubes and the bar can be rotated to provide multiple fore and aft adjustments. Ride on in comfort! Accepts any H-D style male-mount pegs, sold separately.

Tour-Tech™ Cruise Mounts for
 1-1/4-Inch Engine Guards
 

These Cruise Pegs with positive locking Quick Clamps offer an incredible range of adjustability. The entire assembly may be moved up or down on the engine guard. The arm and footpeg may be further adjusted along a vertical or horizontal arc. A unique clevis permits angle adjustment of the footpeg.

The heavy duty Quick Clamp and sturdy offset arm insures that the footpegs will clear fairing lowers and will stay where you put them! Tour-Tech Cruise Peg Mounts are available by themselves, permitting the use of most H-D style male mount peg, or with a variety of Küryakyn footrests.

Recommended for: H-D touring models, FLSTC, or any model using 1-1/4" Engine Guards

 Works great with Fairing Lowers! Sold in pairs.

Adjustable Cruise Pegs for Sportster

These super adjustable cruise pegs for Sportsters are quick and easy to install and provide a wide range of adjustment. They bolt securely to the welded cross brace near the bottom of the downtubes and work equally well on models wit or without forward controls. Accept any H-D style male mount footpegs.

Cruise Boards for Engine Guards

Leave it to Küryakyn to come up with a better Cruise Board System for H-D engine guards. Plant your foot on one of these new boards and you'll see what we mean.

First you'll notice that your foot comes to rest against a built in heel stop. Adjust them to any angle you choose and your foot will be supported comfortably; no effort is needed to keep your foot on the board.

The shape of the board and the vibration isolating rubbers have also been designed to provide more support and greater comfort.

Aside from the aesthetics, a completely new mount has also been developed. Similar to our Magnum Quick Clamps, this clamp simply folds around the engine guard and is secured with one bolt. The new interlocking tooth angle adjustment securely holds the mount in any attitude you place it.

These super trick cruise boards mount to all 1-1/4" engine guards and work great with fairing lowers too! Board measures 8" long and 4" wide at widest point.

Switchblades with Clevis & Clamp

U.S. Patent # Des. 411,440 and U.S. Patent # Des. 506,707
 

ISO™-Pegs With Clevis & Clamps
 

U.S. Patent # Des 411,440

Our most popular cruise pegs! With the trusted Magnum™ Quick Clamp!
 

Pilot™ Pegs with Offset Mounts & Clamp


U.S. Patent # Des 411,440

Offset Mounts with Quick Clamps

U.S. Patent # Des 411,440

Küryakyn offsets provide nearly infinite adjustability for riders of all shapes and sizes - tall, short and in-between.
T.S.I. Pegs with Quick Clamps U.S. Patent # Des 411,440

Longhorn Offset Dually Highway Pegs


U.S. Patent # Des 411,400 and 405,393

The all-in-one answer for long-haul comfort. We combined our most popular highway peg components into one product that’s attractive, adjustable and easy to install.
 

ISO™-Stirrups with Clevis and Magnum™
 Quick Clamps


U.S. Patent # Des 411, 440; 338,643

This setup permits the use of the ISO-Stirrups on 1-1/4" engine guards.
 

Pilot™ Peg with Clevis & Clamp
 

The Pilot Pegs‘ flowing teardrop profile complements the shape of components found on some of today’s cutting-edge customs.

Add to this a full-coverage brake pedal pad. Now the back side of your brake pedal will look as good as the front.

With Pilot Pegs you get the same versatility as with the ISO and Retro pegs.

Longhorn Offset Peg Mount

U.S. Patent # Des 411,440

An extended version of our popular 7996. It's 3-1/4" radius give an incredible 6-1/2" range of adjustment. It's gently curved shape keeps the peg tucked in toward the center line of the bike for maximum comfort. Incorporating an innovative locking device this mount is guaranteed not to slip.

Universal Cruise Peg Mounts for 1-1/4-Inch
 Engine Guards
 

U.S. Patent # Des 411,440

Although we can't understand why anyone wouldn't want to use our pegs, this setup will allow the use of any H-D style male mount pegs with our innovative Magnum Quick Clamps and Clevises for engine guard applications.

Footpeg Offsets

These peg offset mounts are available for a variety of applications. Whether used on an engine guard with our Magnum™ Quick Clamps, on highway peg mounts or forward control plates, under seats etc., nearly every peg location on a bike can be tailored for taller or shorter riders. They can be added to most Küryakyn peg configurations. Secured with 1/2"-13 bolt.

Magnum™ Quick Clamps

U.S. Patent Des # 411,440

We've made a lot of friends with these. Stainless steel construction for superior strength and hinged construction for fast simple installation. No more stripped bolt heads common of 3-piece designs.

Note: All clamps have a 1/2" hole for peg mount.

Diamond D Peg Extension Kits

These kits allow you neatly and easily install a highway peg on your Road King or Dresser. The mounts are machined from billet 6061 aircraft aluminum and show chrome-plated. Stainless steel mounting hardware is included. Four different lengths are available to outfit any rider. See application information to choose the size that’s right for you.
Footpegs and clevises are sold separately. Diamond D extension kits will accept any footpeg clevis with a 1/2" mounting hole. The extensions include 1/2" -20 stainless hardware. If you choose to use mounts with 1/2" -13 threads, hardware may need to be sourced separately.

Diamond D Peg Extension kits will work on most 1-1/4" engine guards. However, the engine guard must be vertical where you intend to mount them. For applications other than those listed, use the length dimensions given to make your selection as to which P/N will work best.

Replacement Clevis for Küryakyn Offsets

This clevis is a direct replacement for use in any Kuryakyn offset. It is also used in the Upper Shock Mount Offsets for Dyna (P/Ns 7973 and 7994) and the Underseat Peg Mounts for Softail (P/Ns 7959, 7960).

Replacement Screws and D-Washers

These screws and D-washers can be used to replace lost or damaged pieces in any of our Magnum style peg mounts. These mounts are found in virtually all of our highway peg assemblies.

Footpeg Mounting Clevises

Footpeg Mounts

X-Tension

This footpeg mount allows one to fine tune their riding position. Measuring 4-1/2" long with a 1-1/4" offset, the rider may now increase or decrease the reach to the highway peg.

The X-Tension mounts with a 1/2"-13 bolt and may be used on OEM highway peg mounts, some forward control plates, with Magnum Quick Clamps, etc. It will accept any H-D style male mount footpeg.

Adjustable Lockable Offsets

Can be used to reposition any male mount footpeg.

 Offered in two lengths - 2" or 4"

 Both male end and clevis can be rotated 360 degrees and lock securely when tightened.

 Investment cast and chrome plated for strength and durability.

Note: Not recommended for use on mounts fastening to the motorcycle with only a single fastener. Leverage applied by the board will cause the mount to "twist" and loosen from the motorcycle. We recommend Anti-Rotation Peg Mounts, P/N 4548, when using these on '00-later Softails.

Male Mount Lockable Offset

The cogged head lets you adjust the offset for greater flexibility in a wide variety of applications without fear of slippage. 2" and 4" versions are offered to fill the bill for highway pegs, passenger pegs, or any H-D style male mount application. Tapered end accepts any Küryakyn footpeg (sold separately).