- Choice of 10 User Selectable Built In Brake Light Strobe/Flash Patterns (User can also select no Strobe/Flash on Brake)
Pattern 0: Four Flashes then Solid (Incandescent or LED)
Pattern 1: Four Flashes, Solid for 3 Seconds, Repeat (Incandescent or LED)
Pattern 2: Seven Flashes then Solid (Incandescent or LED)
Pattern 3: Seven Flashes, Solid for 3 Seconds, Repeat (Incandescent or LED)
Pattern 4: Quad Strobe, then Solid for 1 Second then Quad Strobe (LED Only)
Pattern 5: Quad Strobe, Solid for 1 Second, then Quad Strobe, Solid for 3 Seconds, Repeat (LED Only)
Pattern 6: Custom LED Blaster X Cycle for 3 seconds, then Solid (LED Only)
Pattern 7: Custom LED Blaster X Cycle, Repeat (LED Only)
Pattern 8: Max Strobe 4 Seconds, Solid (LED Only)
Pattern 9: Constant Max Strobe Pattern (LED Only)
- Ability to apply Brake Strobe/Flash Patterns on Center Taillight only, Rear Turns Only, or Rear Turns & Center Taillight
- SMART Function - If Brake Strobe/Flash is Turned On, Strobe/Flashing will be paused on Turn Signal if Simultaneous Braking and Turning
- 10 User Selectable Running Light Intensities Allow User to Match the Running Light Brightness of Turns to Center Taillight
- Built In Short Circuit Protection
- Sealed, Weather Tight Case
- Slim Line Design: 4.2" x 1.4" x 0.6"
- 5 Year Warranty
- Power By
** The use of this product requires a Signal Stabilizer or Load Equalizer. (2011-2012 Softails and 2012 Dynas do NOT require a Signal Stabilizer or Load Equalizer)
Plug and Play on '96-'10 Softails, '97-'11 Dynas, '97-'13 Touring (except Street Glide & Road Glide Custom), and
'99-'03 Sportsters, '10-'13 HD Trikes; '11-'13 Road Glide Ultra
(2011-2012 Softail , & 2012-2013 Dynas With Can Bus does not require a Load
Equalizer, Turn Signals will flash at proper rate.
Alarm Compatible, No Heat, No Load, 100% Waterproof
Plug and Play Module for Honda, Yamaha Cruisers,
Suzuki, & Kawasaki
Change your turn signals into running, turn and brake lights and light up the back of your motorcycle for increased visibility. This plug and play controller connects directly into the stock OEM wiring harness under the seat with no need to splice any wires. Simply finish off the installation with the required red turn signal lenses, or bulbs if you have clear lenses, for the rear of your motorcycle.
Includes one 4807, second 4807 may be
necessary if LEDs are used both front and rear.
Note: Adds optional pulsating brake light function. Rear running lights on a
motor vehicle must be
red.
Plug and Play Run-Turn-Brake Controller for Honda (set) Fits: '04-'08 VTX 1800/S/T, '05-'07, VTX 1800C,
Plug and Play Run-Turn-Brake Controller for Yamaha
(set) Fits: All '04-'10 Road Star 1700 (except Warrior), all '04-'09
V-Star 1100 & All '04-'10 VStar 650, '07-'10 V-Star 1300, '09-'10 VStar 950
Make sure you are seen on the open road! This kit allows
you to change your stock turn signals into Run-Turn-Brake lights with easy
Plug & Play installation. The optional flash mode flashes the taillights
when the brakes are hit - catching the attention of anyone behind you.
This kit includes Plug and Play Run-Turn-Brake Controller and replacement
lenses or bulbs to update turn signals to Red.
Includes one 4807, second 4807 may be
necessary if LEDs are used both front and rear.
Note: Triple Whammy includes everything you need for installation
on motorcycles equipped with OEM turn signals. Installation of this product
may be in violation of FMVSS #108
Triple Whammy Run-Turn Brake Light Kit for Yamaha (set) Fits: All ‘04-‘10 Road Star1700 (except Warrior),
all ‘04-‘09 V Star 1100 & all ‘04-’10 V Star 650, all ‘07-’10 V Star
1300,
‘09-‘10 V Star 950
